In late 2022, the University of Maine's Advanced Structures and Composites Center (ASCC) unveiled the “BioHome3D,” a 600-square-foot single-family unit which it says is the world’s first 3D-printed, 100% bio-based home. Click through the gallery to see inside the house.
There are dozens of 3D-printed homes across the world, but most are built with concrete. The BioHome3D home was printed with wood residuals and bio-resin and uses wood fiber for insulation.
The kitchen in the BioHome3D. Researchers are working on incorporating insulation and conduits for things like electric wires and plumbing into the printing process.
The living room of the BioHome3D. The printed walls give the home a warm and inviting feeling.
A view into the bedroom and the bathroom of the BioHome3D. The home’s modules were prefabricated, then bolted together on site.
The bedroom of the BioHome3D. Maine’s sawmills produce wood residuals that can be used for 3D printing.
Another view of the bedroom in the BioHome3D. The home is recyclable; it can be ground up and the material can be used to 3D print something else.
The bathroom of the BioHome3D. Thousands of people have toured the home. Many ask, “When can I have one?”, says Habib Dagher, the executive director of the university's ASCC.
A look inside the world’s first 3D-printed, 100%-bio home
CNN —
Dozens of 3D-printed homes have been built across the world – to house a family in the US state of Virginia or members of an impoverished community in rural Mexico. The world’s largest 3D-printed neighborhood is currently under construction outside of Austin, Texas.
The technology could be especially handy in a place like the US state of Maine, where approximately 80,000 new homes will be needed by 2030 to address a shortage, according to a report released last year by three state agencies.
“People can’t find homes, they’re very expensive. We also have an aging population … so there’s less and less people who are electricians, plumbers, or builders,” Habib Dagher, the executive director of the University of Maine’s Advanced Structures and Composites Center (ASCC), told CNN via video call.
He says he’s got a solution. Last month, the ASCC unveiled what it says is the world’s largest polymer 3D printer. Dagher hopes the-so-called “Factory of the Future 1.0” can help address the state’s housing crisis – and revolutionize 3D-home-printing in the process.
“The approach we’ve taken is quite different from what you’ve seen, and you’ve been reading about for years,” he says.
A home every 48 hours
In recent years, 3D-printing has been used to build everything from businesses to bridges to mosques. One non-profit is even working on printing schools in a war zone. Dubai, in the United Arab Emirates, holds the Guinness World Record for the world’s biggest 3D-printed structure and aims to have 25% of new buildings constructed with 3D printing technology by 2030.
A great majority of current printing relies on concrete, with a robotic arm equipped with a nozzle layering wet concrete into the right shape.
ASCC is flipping the script. Its giant printer, and its predecessor, which in 2019 was certified by Guinness World Records as the “largest prototype polymer 3D printer,” are the only printers building homes with wood residuals, says Dagher.
This timelapse video shows the world’s largest 3D printer printing a house module.
The technology has already been tested. In late 2022, the university unveiled the “BioHome3D,” a 600-square-foot single-family unit which it says is the world’s first 100% bio-based 3D-printed home, built from local wood fiber and bio-resin materials.
“When they’re doing concrete, they’re only printing the walls,” says Dagher. He adds that the floor, roof and walls of the BioHome3D were all printed.
Concrete homes also need to be built on site, he says. That can be problematic, especially during the snowy New England winter. “When the weather goes bad for two weeks at a time, you can’t print,” he adds.
By contrast, ASCC printed prefabricated modules at the university and bolted them together on site to create BioHome3D.
The new printer can produce objects as large as 96 feet long by 32 feet wide by 18 feet high and can print up to 500 pounds per hour. Dagher says that the goal is to be able to print 1,000 pounds of material in an hour. At that rate, it could reproduce the BioHome3D in 48 hours, he says.
If they can reach that target, their 3D-printed homes will be “very competitive with current housing construction costs,” he adds.
But it can be difficult to process wood materials at such a high speed. Even ASCC’s record-breaking printers sometimes jam. While printing BioHome3D, for example, the printer stopped working due to a dust buildup. “Nobody’s ever done this before with these kinds of materials,” says Dagher.
‘When can I have one?’
The BioHome3D’s warm wooden floors and walls give it the look of a sleek, modern Scandinavian-inspired log cabin.
“Many people feel concrete is a cold thing to look at and it’s not necessarily where you want to live,” says Dagher. The BioHome3D, however, is “very warm and inviting.”
It’s also sustainable. When a home is no longer needed or wanted it can be ground up and used to print something else. ASCC is using wood residuals from Maine’s sawmills in its research, and looking into scaling up production using these local byproducts.
A close-up view of a wall in the BioHome3D. The walls, floors and roof of the home were all printed.
Thousands of people have toured the prototype on the university’s Orono, Maine campus, and Dagher says it’s a rare occurrence when a visitor doesn’t ask, “’When can I have one?’”
“We hear, ‘You know, I’m retiring, and I want to downsize. Can I put one of these up?’” Dagher says.
There are some obstacles to overcome first. “It takes years for codes to change,” says Dagher, referring to building codes that construction companies must meet.
The printer won’t displace traditional home construction, but in the future 3D printed homes are likely to comprise a larger share of the world’s housing stock, he predicts.
The ASCC is now doing work on how to incorporate conduits for wiring and plumbing “exactly where an architect would want them” into the printing process, he adds.
The printer’s next big project is a nine-home neighborhood for people experiencing homelessness. ASCC is partnering with a local NGO to design the structures, and printing is set to kick off in 2025.
